Best Coilovers and Shocks for a Gen 2 Raptor
Upgrade your Gen 2 Raptor's suspension with the best coilovers and shocks. Find detailed reviews and pricing for popular mods.
Gear in this article

For a 2017-2020 Gen 2 Raptor (3.5L EcoBoost), the two suspension upgrades worth real money are a [King 3.0](/mods/king-30-ibp-front-coilovers) IBP front coilover kit paired with King's matching rear bypass shocks, or a Fox 3.0 Factory Race Series internal bypass coilover kit up front. Both land in the $3,500-4,000 range for the front pair alone and need a full shop day to install correctly. If that is more truck than how you actually drive, the [ICON 3.0 VS CDCV](/mods/icon-30-vs-cdcv-coilover-kit) kit is the bolt-on path that resets ride height and adds real compression control for roughly $3,200-4,300, without touching your control arms or your alignment specs more than a normal coilover swap already does.
This guide covers Gen 2 only (2017-2020 F-150 Raptor, 3.5L EcoBoost, factory Fox 2.5 Internal Bypass shocks from the dealer lot). Gen 3 trucks (2021-present) ship with a different factory setup, some with Live Valve electronic damping, and the Gen 3 live valve suspension explainer covers what upgrading that system actually costs. If you are cross-shopping a Gen 2 against a newer truck, start with the Gen 2 vs Gen 3 buying comparison before you spend on suspension.
Why owners upgrade off the stock Fox 2.5 shocks
The factory Fox 2.5 Internal Bypass shocks on a Gen 2 are good shocks for a half-ton truck doing 45 mph in the desert. They are not built for a truck running 37s at speed over whoops for extended stretches, or for a truck that has added real payload up front with a winch bumper. Owners push toward 3.0-series dampers (coilovers and shocks with a 3-inch shock body instead of the stock 2.5-inch body) because the bigger body holds more oil, runs cooler under sustained hard use, and in King's and Fox's cases, adds a remote reservoir that moves heat and fluid capacity off the shock body entirely.
The 3.0 upgrade path is not about ride height, though most kits reset it an inch or two. It is about not cooking your dampers on a long whoop section or a multi-hour run at Glamis or Johnson Valley. If your Raptor sees pavement five days a week and dirt roads on vacation, you may not need any of this, and the lift kit reality check is worth reading before you spend four figures chasing a problem you do not actually have.
King vs Fox vs ICON: the three real options
| King 3.0 IBP Front | Fox 3.0 IBP Front | ICON 3.0 VS CDCV | |
|---|---|---|---|
| Front pair price | roughly $3,950 | $3,540-$3,880 | $3,200-$4,300 |
| Install time | 6-8 hours | 5-7 hours | 5-7 hours |
| Owner rating (mod database) | 4.7/5 | 4.6/5 | 4.3/5 |
| Reservoir | Remote, external | Internal | Remote, external |
These are the mod database's own listed prices and owner-reported ratings as of this writing, not a RaptorCentral test score. Any single figure here should be read as the database's current listing, not a guaranteed out-the-door number. Street pricing moves with reservoir mount style, whether you buy the kit with or without a clicker (external compression adjuster), and whatever markup the shop installing it adds on top.
For an actual back-to-back on how each of these three behaves in the dirt rather than just on paper, the King vs Fox vs ICON whoops test runs all three through the same section of washboard and reports where they separate.
King 3.0 IBP Front Coilover Kit
The King 3.0 IBP Front Coilover Kit fits 2017-and-up F-150 Raptor, which covers both Gen 2 and Gen 3. It is a remote-reservoir coilover, meaning the oil and nitrogen charge live in a separate canister connected by a hose instead of inside the shock body, which is why it tolerates sustained hard use better than an internal bypass unit of the same size. The owner rating on the mod database sits at 4.7/5, the highest of the three front options here, and most of the complaints that do show up are about reservoir clearance against factory skid plates rather than the damper itself.
Budget roughly $3,950 for the front pair per the mod database's listed price, treat that as a current snapshot rather than a locked-in figure, and plan on 6-8 hours of labor if a shop is doing the install, more if they also have to fabricate or relocate a reservoir mount.
Fox 3.0 Factory Race Series Internal Bypass
The Fox 3.0 Internal Bypass shocks are coilovers too, not bare shocks. They carry an integrated coil spring with threaded preload and ride-height adjustment built into the body, and the bypass tubes (internal passages that change how much oil moves at different points in the stroke) give Fox's characteristic progressive damping without needing an external reservoir. That packaging is the appeal: no reservoir to clock around a skid plate, no hose to route and protect.
The tradeoff is heat capacity. Without a remote reservoir, an internal bypass shock runs hotter on long, hard runs than a King or ICON with external oil capacity. For most Gen 2 owners doing weekend trips and the occasional dune day, that is not a real-world problem. For someone doing extended high-speed desert running, it is the reason some owners still choose the reservoir-equipped kits instead. Mod database pricing runs $3,540-$3,880 for the front pair, with a 5-7 hour install and a 4.6/5 owner rating.
ICON 3.0 VS CDCV Coilover Kit
The ICON 3.0 VS CDCV Coilover Kit is built for 2017-2020 Raptors, meaning Gen 2 only. Gen 3 trucks use a different ICON kit built around a CDEV valve rather than the CDCV unit covered here, so confirm which generation a listing is actually for before you buy. CDCV stands for compression damping control valve, an external adjuster on the reservoir that lets you dial compression damping without pulling the shock apart.
This is the bolt-on path in the truest sense: no cutting, no relocating brackets, and it resets ride height while adding real adjustability over the stock Fox 2.5 setup. It does not match the sheer oil volume or adjustability range of the King or Fox 3.0 kits, which shows up in the 4.3/5 owner rating, the lowest of the three, though still solidly positive. Expect $3,200-$4,300 for the front pair and a 5-7 hour install, and treat that spread as real: ICON's current VS/CDCV pricing moves with reservoir mount and clicker options more than the King or Fox kits do.
What about the rear
Front coilovers address ride quality and small-bump compliance where you feel it most, behind the steering wheel. The rear axle on a Gen 2 still rides on leaf springs, and a stiffer front end without addressing the rear just moves the harshness to the back seat.
Two upgrades handle the rear, and they solve different problems:
- [King 3.0 Bypass Shocks - Rear](/mods/king-30-bypass-shocks-rear) replace the factory rear dampers with the same 3.0-body, remote-reservoir technology as King's front coilover. This is a damping upgrade, not a spring upgrade, and it is the natural pairing if you went King up front, since matched valving front-to-rear keeps the truck balanced instead of fighting itself in the whoops. We do not have a clean current price for this piece; expect it to land somewhere in the same neighborhood as the front kit once you account for the remote reservoirs, and pull the live number off the mod database page before you budget a build sheet around it.
- [Deaver Add-a-Leaf Pack](/mods/deaver-add-a-leaf-pack) addresses a different symptom: squat under load and axle wrap (the rear axle twisting against the leaf springs under hard acceleration or heavy payload until the springs let go and snap it back). This is a spring-rate fix, not a damping fix, and it is the cheapest, fastest mod on this whole list. Mod database pricing runs $1,599-$1,631 with a 1-2 hour install and a 4.8/5 owner rating, the highest of anything covered here.
If you tow, carry a bed full of gear, or run a heavy rear bumper, the Deaver pack solves a real problem the King rear shocks will not touch. If your rear end already sits level and you just want better control over bumps, the King rear shocks are the better dollar. Plenty of serious builds run both.
Control arms: the part people forget
A longer-travel front coilover only delivers its full travel if the factory upper control arm can swing through that whole range without binding. The stock Gen 2 upper control arm uses rubber bushings designed around the stock shock's travel, and once you add a 3.0 coilover with more droop, the factory arm can hit its internal stop before the shock does, which defeats the point of the upgrade.
Camburg's KINETIK Series Uniball Upper Control Arms replace the rubber bushings with heim-jointed uniballs (spherical bearings that allow the arm to articulate through a wider range without binding). This matters more once you have already installed a longer-travel coilover; running these arms on an otherwise stock truck gets you less benefit. Mod database pricing sits around $1,899, with a 4-6 hour install, and plan on a wheel alignment afterward since the uniball geometry changes camber curves versus the stock bushing.
Owner rating on these is 4.1/5, lower than the shock options above, mostly tied to installers needing to re-torque and re-check uniball preload correctly, a step some shops rush. Torque the uniball jam nuts and control arm bolts to the value in the current Ford workshop manual for your model year, not to a forum number, including ours.
Total build cost by path
| Build | Parts total (approx.) | Labor |
|---|---|---|
| King front + King rear | roughly $3,950 front, rear priced separately | 10-14 hours combined, estimate |
| Fox front + Deaver rear pack | $3,540-$3,880 + $1,599-$1,631 | 6-9 hours combined, estimate |
| ICON front + Deaver rear pack | $3,200-$4,300 + $1,599-$1,631 | 6-9 hours combined, estimate |
| Add Camburg UCAs to any of the above | roughly +$1,899 | +4-6 hours, plus alignment |
These are parts figures from the mod database, not out-the-door quotes, and the labor hours are estimates that will swing with how a given shop sequences the job. Add sales tax, shop supplies, and whatever your installer charges for shop time, which varies hard by region and whether you are at a dedicated off-road shop or a general repair bay. Get an actual quote from whoever is turning the wrench before you commit to a build sheet.
Which path actually fits your truck
If you run 35s or 37s and spend real time on trails like those covered in the best places to off-road a Raptor guide, the King front and rear combination with Camburg uniballs is the setup most owners who actually use their trucks hard end up building toward, even if they get there in stages. If you went to 37s already, the cost of running 37s on a Gen 2 is worth reading alongside this one since tire size changes how much suspension travel you can actually use.
If your Raptor is mostly a daily driver that sees dirt on weekends, the ICON kit plus a Deaver add-a-leaf pack gets you most of the ride-quality improvement without the remote-reservoir plumbing or the control-arm swap, and it is the cheaper path by roughly $1,500-2,000 all-in, depending on which front kit you are comparing against.
Skip all of it if your truck is stock tires, stock ride height, and mostly pavement. The factory Fox 2.5 setup is tuned well for that use case, and the money is better spent on tires or a pre-purchase inspection if you are still shopping.
The short version
- King 3.0 IBP front + King 3.0 rear bypass shocks: the highest-rated, most capable combination for a Gen 2 run hard, roughly $3,950 for the front pair plus a separately priced rear kit, 10-14 hours of combined labor as an estimate.
- Fox 3.0 Factory Race Series: cleaner packaging, no reservoir to route, slightly less heat capacity on long hard runs, $3,540-$3,880 for the front pair.
- ICON 3.0 VS CDCV: the bolt-on path for Gen 2 only (2017-2020), $3,200-$4,300 for the front pair, least adjustability of the three but still a real upgrade over stock.
- Pair any front coilover with a Deaver add-a-leaf pack if you tow or carry weight, or King rear bypass shocks if your rear ride height is already fine and you just want matched damping.
- Add Camburg uniball upper control arms only once you have a longer-travel coilover installed, torque everything to the current Ford workshop manual spec for your model year, and budget for an alignment afterward.
Deal alert
Shopping for one? Get new listings first
We sweep US dealer inventory and send you new Raptors matching your search — real listings, real asking prices, no spam.