Skip to content
RAPTORCENTRAL

Toyota 4Runner · 5th gen

Toyota 4Runner lights

Bolt-in fog pocket pods, hood ditch lights and a roof rack bar are the proven 5th gen setup, and you will need your own switch and relay because there are no factory AUX switches. On 2020 and later trucks the TSS radar sits behind the grille, so pick grille kits that list TSS compatibility for your trim.

Years
2010 to 2024
Upfitter switches
none
Mount points
4

Where lights go on the Toyota 4Runner

Each mount point below says what fits on this truck and links to its source. Checked 2026-11-15.

Ditch (A-pillar)

Ditch brackets put two pods above the hood using factory mounting points with no cutting or drilling, and do not interfere with opening the hood.

Example: Diode Dynamics Stage Series Backlit Ditch Light Kit for 2010-2024 Toyota 4Runner

Fog pockets

On 2014 to 2024 4Runners, Diode's SS3 kit bolts in where the factory fog assembly comes out and plugs into the factory bulb sockets, and it fits all trims including Limited, TRD Pro and ORP. 2010 to 2013 trucks use a separate kit.

Example: Diode Dynamics SS3 LED Fog Light Kit for 2014-2024 Toyota 4Runner

Grille

Two or four 5 in pods mount behind the factory grille on brackets that bolt to the factory bumper, with no drilling, on 2014 to 2024 trucks; not compatible with the Limited or Nightshade. A fifth center pod only fits 2014 to 2019 trucks without Toyota Safety Sense.

Example: Diode Dynamics SS5 Stealth Grille LED Pod Kit for 2014-2024 Toyota 4Runner

Roof

KC's Platform One rack bolts to factory mounting points without drilling and carries a 50 in Gravity Titan bar plus four 10 in side lights.

Example: KC HiLiTES Platform One Roof Rack with 360 Lighting, Toyota 4Runner 2010-2024 (AK-92305)

Switches and wiring

The 5th gen 4Runner owner's manual has no auxiliary switch section, so added lights need an aftermarket switch and relay harness.

Anything bigger than a small pod should run through a relay, with the switch only triggering the coil. The wiring calculator gives the fuse, relay and wire gauge for your lights, and how to wire a light bar walks through the job.

Factory lighting

  • Fog lights (All grades (2022, LED); TRD Pro (Rigid Industries LED)): For 2022 Toyota says all 4Runner models have LED fog lights as standard, with Rigid Industries LED fog lights on the TRD Pro. The factory fog housings are the common mount for bolt-in replacement pods. Source: pressroom.toyota.com ↗
  • Off-road lights from the factory: No factory light bar; the TRD Pro gets Rigid Industries LED fog lights. Source: pressroom.toyota.com ↗

Watch out for

  • On Toyota Safety Sense P trucks the radar sits behind the front grille, and Toyota calls for recalibration if the radar or grille is removed and reinstalled or the front bumper is replaced. Source: toyota.ca ↗
  • Diode's upper grille light bar kit fits all 2014 to 2019 trims but only the TRD Pro on 2020 to 2024, and Diode says the TRD Off-Road Premium grille blocks the bars. Source: diodedynamics.com ↗
  • Trucks with intuitive parking assist have front corner sensors in the bumper, which bumper lights must not cover. Source: toyota.ca ↗
  • Off-road lights must be off on public roads in most states, and some states want them covered. Check your state.

Research note: Toyota manual used is OM35C03U (4RUNNER (U), Toyota Safety Sense P, so 2020 or later) from toyota.ca; exact model year not confirmed, and no AUX switch section was found in it or in pre-2020 manual OM35B23U. Fog lamp trims are confirmed for 2022 only (Toyota press release); 2010 to 2021 and 2023 to 2024 fog availability by trim and the year Rigid fogs began on the TRD Pro were not confirmed from Toyota. Front corner sensor detail comes from the intuitive parking assist section (if equipped); Toyota's 2022 release names front and rear clearance sonar as standard on the Limited only. Diode's 2010-2024 ditch kit page lists bracket DD6745P as 2010-2021 in its parts table, so 2022 to 2024 bracket fit should be confirmed with Diode. No pages blocked during this run.

Common questions

What is the best way to add lights to a 2010 to 2024 Toyota 4Runner?
Bolt-in fog pocket pods, hood ditch lights and a roof rack bar are the proven 5th gen setup, and you will need your own switch and relay because there are no factory AUX switches. On 2020 and later trucks the TSS radar sits behind the grille, so pick grille kits that list TSS compatibility for your trim.
Does the 2010 to 2024 Toyota 4Runner have upfitter switches?
The 5th gen 4Runner owner's manual has no auxiliary switch section, so added lights need an aftermarket switch and relay harness.
How do you mount ditch lights on a 2010 to 2024 Toyota 4Runner?
Ditch brackets put two pods above the hood using factory mounting points with no cutting or drilling, and do not interfere with opening the hood.
Can you put LED pods in the 2010 to 2024 Toyota 4Runner fog light pockets?
On 2014 to 2024 4Runners, Diode's SS3 kit bolts in where the factory fog assembly comes out and plugs into the factory bulb sockets, and it fits all trims including Limited, TRD Pro and ORP. 2010 to 2013 trucks use a separate kit.
Can you put a light bar on the roof of a 2010 to 2024 Toyota 4Runner?
KC's Platform One rack bolts to factory mounting points without drilling and carries a 50 in Gravity Titan bar plus four 10 in side lights.
Does the 2010 to 2024 Toyota 4Runner have factory fog lights?
For 2022 Toyota says all 4Runner models have LED fog lights as standard, with Rigid Industries LED fog lights on the TRD Pro. The factory fog housings are the common mount for bolt-in replacement pods.

Keep going