Skip to content
RAPTORCENTRAL

Wiring calculator

Light bar wiring calculator

Add up the amp draw of every light on the circuit, fuse at the next size above 125 percent of that, and run it through a 30 or 40 A relay. A typical 30 inch LED bar pulls about 13 A, so it takes a 20 A fuse and 16 AWG wire to the bumper, or 12 AWG to the roof.

Lights loaded
125
Voltage drop target
5%
Fuse rule
125% of load
Start from a setup
Your lights
  • Diode Dynamics SS30 Pro 30" driving
    12.9 A each
    1
Not listed? Add it by its rating
Wire run, battery to lights (one way)
Total draw
12.9 A

1 lights

Circuits
1

one relay

Fuse
20 A
Wire
16 AWG

8 ft run

12.9 A

1 × Diode Dynamics SS30 Pro 30" driving
  • Fuse: 20 A blade fuse in an inline holder, within 7 in of the battery.
  • Relay: 30 A automotive relay (Bosch style, 4 or 5 pin).
  • Power and ground wire: 16 AWG copper, red for power, black for the ground lead. 4.7% voltage drop over the 8 ft run.
  • Switch side: any AUX switch can trigger the relay; AUX5 (5 A) keeps the bigger circuits free.
Battery+−to chassis20 A fusewithin 7 in of battery16 AWGRelay30878586Upfitter AUX5switches the relay coil (under 0.2 A)16 AWGDiode Dynamics SS30 Pro…ground to chassis, same gaugePowerGroundSwitch trigger

Swipe to see the whole diagram.

At 12.9 A this is more than 75% of every 2021+ F-150 Raptor (Gen 3) or Tremor AUX circuit (the biggest is 15 A), so the relay is required. Ratings from the Ford 2022 and 2024 F-150 owner's manuals (lower of the two published figures); find the AUX wires.

Parts list

  • 30 A automotive relay, 20 A fuse and holder, about 14 ft of 16 AWG (red and black)
  • Ring terminals for the battery and a chassis ground, heat-shrink butt connectors, split loom
  • About 15 ft of 18 AWG to reach the AUX wire for the relay trigger

Most light kits include a harness with a relay, fuse and switch. Check its wire gauge against the number above before you use it on a long run.

Wire gauge chart: AWG by load and run length (one way)
LoadFuse8 ft run12 ft run18 ft run22 ft run
3 A5 A18 AWG18 AWG18 AWG18 AWG
5 A7.5 A18 AWG18 AWG16 AWG16 AWG
8 A10 A18 AWG16 AWG14 AWG14 AWG
10 A15 A16 AWG14 AWG14 AWG12 AWG
13 A20 A16 AWG14 AWG12 AWG12 AWG
15 A20 A14 AWG14 AWG12 AWG12 AWG
20 A25 A14 AWG12 AWG10 AWG10 AWG
25 A35 A12 AWG12 AWG10 AWG8 AWG
30 A40 A10 AWG10 AWG8 AWG8 AWG

How the calculator works

Load is the sum of each light's amp draw from the maker's spec sheet, as listed in our light database. Where a maker lists only watts, we divide by 13.5 V. Budget bars often quote a rated wattage well above their real draw, which makes the wire bigger than strictly needed; that errs on the safe side.

Fuse is the next standard blade fuse at or above 125 percent of the load, so it never blows at normal draw but still blows before the wire overheats. Wire is the thinnest copper gauge that is rated for at least the fuse and keeps voltage drop at or under 5 percent (0.6 V). We count the power run plus a 3 ft ground lead to the chassis next to the lights. Ratings are the ABYC E-11 figures for 105 C insulated copper wire, cut 15 percent for engine bay heat.

Circuits: one relay circuit carries up to 32 A of lights, which is 80 percent of a 40 A relay and fuse. Anything bigger is split onto more than one relay.

This is a sizing guide, not a substitute for the light maker's instructions. If the maker calls for a bigger fuse or wire than this page, use theirs.

Common questions

Do I need a relay for my light bar?
Yes for anything over a few amps. The relay lets a small switch circuit turn on a heavy power wire that runs straight from the battery, so the switch and the factory wiring never carry the light's full current.
What size fuse for a light bar?
Take the bar's amp draw, multiply by 1.25 and round up to the next standard blade fuse. A 13 A bar gets a 20 A fuse; a 20 A bar gets a 25 A fuse. The wire must be rated for at least the fuse size.
What gauge wire for a 30 inch light bar?
About 16 AWG for a short run to the bumper and 12 AWG to the roof, for a bar drawing around 13 A. Longer runs need thicker wire to keep voltage drop down; the calculator works it out for your run.
Can I wire a light bar to a Raptor upfitter switch?
Yes. On a 2017 or newer Raptor, use one of the six overhead AUX switches to trigger a relay. The AUX circuits are rated 5 to 15 A depending on the switch, so the relay carries the bar's current, not the factory wire.
Can I put two light bars on one relay?
Yes, as long as the combined draw stays under about 32 A on a 40 A relay and fuse, with wire sized for the total. Past that, split the lights onto two relays; the calculator does this for you.
Where should the fuse go?
As close to the battery as you can, within about 7 inches. The fuse protects the wire, so any wire between the battery and the fuse is unprotected.

Keep going

Updated 2026-11-15.