Skip to content
RAPTORCENTRAL

Light bar wiring

How to wire a light bar

Run a fused wire from the battery to a relay, from the relay to the light bar, and ground the bar to the chassis. A switch in the cab, or a factory upfitter switch, turns the relay on, so the heavy current never goes through the switch.

Time
1 to 3 hours
Typical 30 in bar
13 A, 20 A fuse
Relay
30 or 40 A

Light bar wiring diagram

One 30 inch bar on a relay, triggered by a Raptor upfitter switch. Swap the switch box for a dash switch on any other truck; everything else is the same. The 16 AWG suits a bumper mount; on the roof, the longer run calls for 12 AWG.

Battery+−to chassis20 A fusewithin 7 in of battery16 AWGRelay30878586Upfitter AUX5switches the relay coil (under 0.2 A)16 AWG30" LED light barground to chassis, same gaugePowerGroundSwitch trigger

Step by step

  1. 1

    Work out the load

    Find the bar's amp draw on its spec sheet (or divide watts by 13.5). Add every light that will share the switch. The wiring calculator gives you the fuse, relay and wire gauge for your run.

  2. 2

    Disconnect the battery

    Take the negative cable off first. On a Gen 3 Raptor, plan for the battery management system to relearn afterward.

  3. 3

    Mount the relay and fuse

    Mount the relay somewhere dry in the engine bay, terminals pointing down so water can't sit on them. Put the inline fuse holder within about 7 inches of the battery positive. Leave the fuse out for now.

  4. 4

    Run the power wire

    Battery positive to the fuse holder, fuse holder to relay pin 30. Then relay pin 87 to the bar's positive lead. Use the gauge from the calculator for both legs, in split loom, away from the exhaust and anything that moves.

  5. 5

    Ground the bar and the relay

    Run the bar's negative lead to a clean, bare-metal chassis point near the bar, with a ring terminal and star washer. Relay pin 85 goes to ground as well. On a Raptor, ground to the chassis, not the battery negative post: that post feeds the battery monitor sensor.

  6. 6

    Wire the switch

    Relay pin 86 goes to the switch output. On a 2017 or newer Raptor, that is one of the overhead AUX wires; see the Gen 3 and Gen 2 guides for the wire colours. On other trucks, feed the switch from a 5 A fused key-on source so the bar can't be left on with the truck off.

  7. 7

    Seal, fuse and test

    Crimp and heat-shrink every joint. Reconnect the battery, fit the fuse, turn the key and flip the switch. If the fuse blows at once, look for bare wire touching metal before you try a bigger fuse; never upsize a fuse to make it hold.

What you need

A 30 or 40 A relay and socket, an inline blade fuse holder and fuse, red and black wire in the gauge the calculator gives you, 18 AWG for the switch wire, ring terminals, heat-shrink butt connectors, split loom and zip ties. Tools: wire strippers, a ratcheting crimper, a heat gun and a test light or multimeter.

Common questions

What do the numbers on a relay mean?
On a standard automotive relay, 30 is power in from the fuse, 87 is power out to the lights, 85 goes to ground and 86 goes to the switch. A 5 pin relay adds 87a, which is on when the relay is off; leave it unused for a light bar.
Can I wire a light bar without a relay?
Only a small one, and only if the switch and its wiring are rated for the full current. Most bars draw more than a dash switch should carry, which is why nearly every light bar harness includes a relay.
Should the light bar work with the key off?
Better not. Feed the switch side from a key-on source, like a Raptor upfitter switch, so the bar can't drain the battery overnight.
Is the harness that came with my light bar good enough?
For a short run usually yes. Check the wire gauge printed on it against the calculator: a cheap harness is often 16 or 18 AWG, which is fine at the bumper but too thin for a big bar on the roof.
Is it legal to drive with a light bar on?
In most states, no. Light bars are off-road lights; keep them switched off on public roads, and covered where your state asks.

Keep going

Updated 2026-11-15.