Where lights go on the Ford Bronco Raptor
Each mount point below says what fits on this truck and links to its source. Checked 2026-11-15.
A-pillar ditch kits fit the Bronco Raptor with no cutting or drilling and include a relay harness with toggle switch.
Example: Baja Designs XL80 A-Pillar Light Kit, Ford 2021-2025 Bronco / 2022-2025 Bronco Raptor (670003)
The bumper end cap fog pockets take replacement kits built around the OEM lamps; Baja's S2 SAE and S2 Pro fog pocket kit lists the 2023 to 2026 Bronco Raptor, and Ford Performance sells a Rigid off-road driving lamp upgrade for Bronco Raptors with factory fog lights.
Example: Baja Designs S2 SAE/S2 Pro Fog Pocket Kit; Ford Performance Parts by Rigid Off-Road Driving Lamp Upgrade (M-15200-RDL)
A linkable six light bar mounts to the OEM modular steel bumper and is listed for the Bronco Raptor; Baja warns it may block part of the front camera's view.
Example: Baja Designs 6XL Linkable Bumper Light Kit, Bronco with OEM modular steel bumper (740004)
A 50 in roof bar kit fits the Bronco Raptor with no cutting or drilling, but it will not work with factory roof racks and adds some wind noise.
Example: Baja Designs S8 50 Inch Roof Mount Light Kit (705003)
The spare tire carrier reinforcement has an accessory spot meant for light items such as a light: one M6x1 mm hole rated for up to 3 lb, with Ford recommending a Grade 10.9 fastener.
Example: Factory spare tire carrier accessory mounting point
Switches and wiring
Six AUX switches with pre-run accessory wires sit in the overhead console. The 2023 Bronco manual's Raptor table lists AUX 1 10A (off-road driving lights if equipped), AUX 2 15A, AUX 3 30A, AUX 4 10A, AUX 5 10A and AUX 6 10A. AUX 1 and AUX 3 are swapped compared with other Broncos, and there is an unpowered pass-through circuit to the front grille.
| AUX1 | AUX2 | AUX3 | AUX4 | AUX5 | AUX6 |
|---|---|---|---|---|---|
| 10 A | 15 A | 30 A | 10 A | 10 A | 10 A |
Anything bigger than a small pod should run through a relay, with the switch only triggering the coil. The wiring calculator gives the fuse, relay and wire gauge for your lights, and how to wire a light bar walks through the job.
Factory lighting
- Fog lights (Bronco Raptor): Rigid LED fog lamps and off-road lamps come standard in the removable end caps of the heavy-duty modular front bumper. The lamps unplug from a docking connector when you pull the end caps. Source: ford.com ↗
- Off-road lights from the factory: Rigid LED off-road lamps are built into the front bumper end caps, and the off-road driving lamps run from AUX switch 1. Ford notes they are for off-road use only. Source: fordservicecontent.com ↗
Watch out for
- The adaptive cruise radar is behind a fascia panel in the lower grille, and Ford warns aftermarket lights and front protectors can degrade it. Source: fordservicecontent.com ↗
- Bronco Raptor AUX 1 and AUX 3 wiring is swapped compared with other Broncos, so do not follow a non-Raptor Bronco wiring chart. Source: fordservicecontent.com ↗
- A bumper light bar may sit in part of the front facing camera's view on camera equipped trucks. Source: bajadesigns.com ↗
- The front parking aid sensors are in the front bumper, so bumper mounted lights must not cover them. Source: fordservicecontent.com ↗
- Off-road lights must be off on public roads in most states, and some states want them covered. Check your state.