Where lights go on the Ford Bronco
Each mount point below says what fits on this truck and links to its source. Checked 2026-11-15.
Ditch light brackets bolt to the factory Accessory Ready mounting points near the A-pillar, above the hood, with no cutting or drilling, and hold two 3 in SS3 pods. Diode says the kit will not interfere with the antenna or with opening the hood, and lists 2021 to 2025.
Example: Diode Dynamics Stage Series SS3 Backlit Ditch Light Kit for 2021-2025 Ford Bronco
On the plastic or capable bumper, a bracket kit bolts into the factory fog light mounting points and plugs into the factory sockets, though the inner plastic fog surround needs slight trimming. Ford Performance's RIGID kit fits only 2021 to 2025 Broncos with factory fogs and the Base/Non-Modular bumper, and not Everglades or Bronco Raptor.
Example: Diode Dynamics SS3 LED Fog Light Kit for 2021-2025 Ford Bronco (w/ Standard Bumper); Ford Performance Off-Road Fog Light Kit by RIGID (M-15200K-BFLK)
The modular steel bumper's openings take two SS3 fog pods and four SSC2 off-road pods on a bolt-on bracket, with a harness for the factory aux switch bank; Diode says it does not fit the plastic bumper. Ford Performance also sells a kit that adds Bronco Raptor end caps and RIGID fog lamps to non-Raptor Broncos with the modular bumper and Sasquatch package.
Example: Diode Dynamics Stage Series Fog Pocket Kit for 2021-2025 Ford Bronco (w/ Steel Bumper); Ford Performance Bronco Auxiliary Lighting Kit, Modular Front Bumper (M-15200K-BL2)
A six pod SS5 bar bolts to factory mounting points on the grille with no drilling and connects to the factory aux switches. Diode lists it for Broncos with the steel bumper and warns it may slightly block the front facing camera.
Example: Diode Dynamics SS5 Grille CrossLink Lightbar Kit for 2021-2025 Ford Bronco (w/ Steel Bumper)
A 40 in RIGID light bar installs at a factory Bronco mounting location, with brackets for hard and soft tops, and is built for the factory aux switches or Ford's M-9100-BR switch kit. Trucks with the OE roof rack need a different kit (M-15200K-BRRL), and Ford warns of extra wind noise.
Example: Ford Performance Bronco 40 in RIGID SR light bar kit (M-15200K-BRL); Diode Dynamics SS5 Windshield CrossLink Lightbar Kit
The spare tire carrier reinforcement has an accessory spot meant for light items such as a light: one M6x1 mm hole rated for up to 3 lb, with Ford recommending at least a Grade 10.9 fastener.
Example: Factory spare tire carrier accessory mounting point
Switches and wiring
Six AUX 1 to AUX 6 switches in the overhead console with pre-run accessory wires are standard on the 2026 Badlands and Heritage Edition and come in the Black Diamond package on Big Bend. The 2023 manual's non-Raptor table lists AUX 1 30A, AUX 2 15A and AUX 3 to AUX 6 10A each, and its fuse table agrees (Upfitter 1 Base 30A, 2 15A, 3 Base 10A, 4 to 6 10A).
| AUX1 | AUX2 | AUX3 | AUX4 | AUX5 | AUX6 |
|---|---|---|---|---|---|
| 30 A | 15 A | 10 A | 10 A | 10 A | 10 A |
Anything bigger than a small pod should run through a relay, with the switch only triggering the coil. The wiring calculator gives the fuse, relay and wire gauge for your lights, and how to wire a light bar walks through the job.
Factory lighting
- Fog lights (Fog lamps if equipped (trim list not confirmed from Ford); plastic bumper: Base, Big Bend, Outer Banks, Wildtrak; capable bumper: 2022 and newer Black Diamond, Badlands; modular steel bumper: optional): Front fog lamps are fitted where equipped and Ford's 2023 bulb chart lists them as LED, switched from a button on the lighting control. The fog location differs by bumper: Diode says the standard plastic bumper is on Base, Big Bend, Outer Banks and Wildtrak, and the capable bumper is on 2022 and newer Black Diamond and Badlands, while the optional modular steel bumper has its own fog pockets. Source: fordservicecontent.com ↗
- Off-road lights from the factory: Ford lists optional left and right spot lamps (if equipped), aimed by moving the exterior mirrors, that switch off above 6 mph (10 km/h). The factory off-road driving lamps on AUX 1 are listed for the Raptor only. Source: fordservicecontent.com ↗
Watch out for
- On trucks with adaptive cruise, the radar sits behind the fascia cover in the center of the lower grille, so keep grille and bumper lights clear of it. Source: fordservicecontent.com ↗
- The front view camera is in the grille, and Diode warns its grille light bar may slightly block that camera's view. Source: fordservicecontent.com ↗
- The front parking aid sensors are in the front bumper, so bumper pods must not cover them; Ford Performance sells its modular bumper in park aid and non park aid versions. Source: fordservicecontent.com ↗
- Pick fog kits by bumper type: Diode's steel bumper kit does not fit the plastic bumper, and Ford's RIGID fog kit does not fit Everglades, Bronco Raptor or modular bumper trucks. Source: performanceparts.ford.com ↗
- Broncos without factory AUX switches can add Ford Performance's M-9100-BR kit, which brings a factory switch panel and a fuse block with two 10A relays, one 15A and one 30A. Source: performanceparts.ford.com ↗
- Ford specifies a different battery part number for Broncos with auxiliary switches, so match the battery spec to your truck if you replace it. Source: fordservicecontent.com ↗
- Only the underhood circuits are powered; the pass-through wires to the front grille, right hand visor, right rear quarter panel and passenger compartment are not connected at either end. Source: fordservicecontent.com ↗
- Off-road lights must be off on public roads in most states, and some states want them covered. Check your state.