Where lights go on the Toyota Tacoma
Each mount point below says what fits on this truck and links to its source. Checked 2026-11-15.
A-pillar (ditch) bracket pairs bolt to factory bolt locations with no drilling and take lights up to 6 in. KC notes the brackets may touch and slightly crease the plastic trim.
Example: KC HiLiTES Bracket Set - Pillar / Ditch Mount - Pair - for 16-23 Toyota Tacoma (73502)
Diode Dynamics' SS3 fog kit replaces the factory fog lamps on 2016 to 2023 Tacomas that have OEM fogs, with plug-in adapters to the factory bulb sockets and no modification. It is not compatible with TRD Pro models, and trucks without factory fogs may need extra hardware and wiring.
Example: Diode Dynamics SS3 LED Fog Light Kit for 2016-2023 Toyota Tacoma
A 30 in light bar mounts behind the factory grille on brackets that use factory mounting points, with no cutting or drilling. It is designed for the factory bumper; Diode cannot confirm aftermarket bumpers.
Example: Diode Dynamics 2016-2023 Toyota Tacoma Stealth Lightbar Kit
KC's overhead bracket pair bolts into the factory roof bolt locations above the windshield for a KC Gravity Titan, Pro6, C-Series or FLEX bar. It is Double Cab only and not compatible with the extended cab.
Example: KC HiLiTES Bracket Set - Light Bar - Overhead Mount - Pair - for 05-23 Toyota Tacoma Double Cab (7380)
Switches and wiring
The 3rd gen Tacoma owner's manual has no auxiliary switch section, so plan on an aftermarket switch panel or relay harness for added lights.
Anything bigger than a small pod should run through a relay, with the switch only triggering the coil. The wiring calculator gives the fuse, relay and wire gauge for your lights, and how to wire a light bar walks through the job.
Factory lighting
- Fog lights (TRD Sport, TRD Off-Road, Limited (LED for 2020); TRD Pro (Rigid Industries LED)): Toyota lists LED fog lamps on the 2020 TRD Sport, TRD Off-Road and Limited and Rigid Industries LED fog lights on the TRD Pro; the owner's manual lists bulb type fogs (if equipped) as H16 for the normal type and H11 for the wide angle type. The factory fog location is the common mount for bolt-in aftermarket pods, except on the TRD Pro. Source: pressroom.toyota.com ↗
- Off-road lights from the factory: No factory light bar; the TRD Pro gets Rigid Industries LED fog lights from the factory. Source: pressroom.toyota.com ↗
Watch out for
- The Toyota Safety Sense radar sits behind the front grille, and Toyota says not to put accessories on or around it and to have it recalibrated if the radar or grille is removed and reinstalled or the front bumper is replaced. Source: toyota.ca ↗
- The TSS front camera sits behind the windshield, so nothing that blocks the windshield area in front of it should be mounted there. Source: toyota.ca ↗
- Off-road lights must be off on public roads in most states, and some states want them covered. Check your state.
Research note: Toyota facts come from owner's manual OM04037U (a USA Tacoma manual, 2GR-FKS engine, Toyota Safety Sense P, hosted on toyota.ca); the exact model year of that manual was not confirmed, and it has no AUX switch section. Fog trim list is from Toyota's 2020 press release only; fog availability by trim for 2016 to 2019 and 2021 to 2023 was not confirmed. Diode Dynamics' 2016-2023 ditch kit page contradicts itself (bracket DD6371 is labeled 2016-2021 in kit components and Q&A), so it was not used; KC's 73502 page lists 2016-2023. Retailer leads from toyota-notes.md (ExtremeTerrain DD6254P, Cali Raised roof rack) were superseded by maker pages. The Morimoto, Rago and Cali Raised hood hinge ditch bracket lead was not confirmed on a maker page. bajadesigns.com was not used (reported 403 to fetchers in prior notes). No pages blocked during this run.