Best Armor for a Gen 3 Raptor: Bumpers, Skids, and Sliders
Find the best armor for your Gen 3 Raptor, including front bumpers, skid plates, and rock sliders. Protect your Raptor with trusted mods.
Gear in this article

Armor is the one mod category where "best" actually has a defensible answer: protect the front clip and the oil pan, protect the rockers, and do it without adding so much weight that you undo your brakes and your fuel economy. For a Gen 3 Raptor (2021-present, both the 3.5L EcoBoost and Raptor R 5.2L supercharged V8 trucks), that means a front bumper that does not force a radar recalibration you did not budget for, a skid package that covers the oil pan through the transfer case, and rock sliders rated to actually carry the truck's weight, not just look like they could.
This guide ranks the real options in each category, what they cost, and who should skip them entirely.
Front bumpers: what you lose and what you gain
A Gen 3 bumper swap is not just cosmetic. The factory bumper houses the forward radar for adaptive cruise and the front camera. Any aftermarket bumper worth buying on a Gen 3 either retains the factory radar mount in its stock position or tells you plainly what you lose. If the radar gets moved or removed during install, budget for a recalibration, since that is a dealer or alignment-shop procedure, not something you skip and hope works.
ADD Stealth Fighter Front Bumper
The ADD Stealth Fighter Front Bumper is the one you see most often under a built Gen 3, and it is also common on Gen 2 trucks, which tells you something about how long it has been dialed in. It keeps the factory fog light location, adds approach angle over the stock bumper, and has a recovery point rated for an actual strap or winch pull, not a tow hook rated for parking-lot incidents. It runs around $2,699 at last check, and plan on 6-8 hours of labor if a shop does it, less if you have a lift and have swapped a bumper before. A steel bumper like this does add real weight to the nose, but neither ADD nor most competitors publish an exact figure for how much, so do not trust a specific pound number here, including ours; just plan on the front end feeling noticeably different if you are also stacking a winch on top of it.
ADD HoneyBadger Winch Front Bumper
The ADD HoneyBadger Winch Front Bumper is the lighter, simpler alternative from the same maker. Same winch-ready mount, same D-ring shackle tabs, less steel up front, which means less approach angle gained but a lighter front end, which matters if you are already running 37s and a winch and watching what that does to the steering feel. Price runs $2,799-2,999 at last check depending on finish and whether you add fog lights. Same 6-8 hour install window as the Stealth Fighter.
If you are not winching and do not need the recovery point, neither of these is a necessary purchase. A stock Gen 3 bumper survives normal trail use. Where these earn their keep is washes and rock-strewn approach angles where the stock plastic valance drags or cracks.
Rear bumper: often skipped, shouldn't be
The ADD Bomber Rear Bumper gets less attention than the front, but it is the piece that keeps a departure-angle hit from bending your tailgate and taillight housing into an insurance claim. It is also where a lot of builds mount a spare tire carrier or a receiver-mounted accessory. Pricing on a rear bumper like this swings hard depending on finish, whether you add a tire carrier or lighting, and which cab configuration you are fitting, so treat any number you see online as a starting point and confirm the exact build price before you order.
Skid plates: what actually needs to be covered
Stock Gen 3 skid coverage is plastic from the factory under the engine and not much else. The transfer case, front differential, and transmission pan are exposed on a stock truck, and that is exactly where rocks find you on a rutted trail or a rocky wash approach. If you are running the truck anywhere near rock, not just sand, this is the category to spend on first, before bumpers.
| Package | Coverage | Price (est.) | Install time |
|---|---|---|---|
| Juggernaut USA Full Skid Plate Package | Engine through transfer case, plus front/rear lower control arm shields | $1,565-1,780 | 1-2 hours |
| RCI Full Skid Plate Package | Front diff through transfer case | $660-797 | 4-6 hours |
The Juggernaut package is quarter-inch 5052 aluminum and bolts to factory mounting points with no drilling. The maker lists clearance claims for lifted trucks, but confirm fitment against your exact ride height and tire size before ordering, since those numbers vary with the specific suspension setup underneath. It is also the quicker install of the two because the hardware is purpose-fit rather than requiring you to work around factory brackets.
The RCI package is the budget path to similar coverage, replacing the factory plastic that cracks on the first real rock strike with quarter-inch aluminum from the front diff back to the transfer case. It takes longer to install because the fitment is less turnkey, but the price gap is real money saved if your labor is free.
RCI also sells a standalone transfer case skid plate. If the budget only covers one component, the transfer case is the single highest-consequence spot to protect, since a cracked case housing on the trail is a tow, not a limp home. We do not have current standalone pricing we trust enough to quote here, so check current listings before you assume it costs meaningfully less than the full package just because it covers less ground.
Rock sliders: the difference between a dent and a trip home
Rock sliders protect the rocker panels and door sills when you drop a tire into a rut or lean the truck against a boulder on a tight line. On a Gen 3 SuperCrew, factory running boards are cosmetic and will fold under real sidewall contact.
The RCI SuperCrew Rock Sliders are the common choice here, bolt-on with no welding required on most Gen 3 cabs. Budget $1,239-1,499 and 3-5 hours of labor, less if you have already pulled the factory running boards. Beyond crash protection, a slider rated to take the truck's weight also doubles as a step and a jacking point if you carry a hi-lift or bottle jack setup for trail repairs.
Sliders are one of those mods where cheap aftermarket tube sliders can be worse than nothing: a slider that is not rated to carry the vehicle's weight will bend inward on a hard hit and can push into the rocker panel harder than if it were not there at all. If you are shopping on price alone here, you are shopping wrong.
How to prioritize if you can't do all three at once
Most owners build armor in stages. If you are budgeting across a year instead of one purchase, the order that makes sense for most Gen 3 trucks running actual trail miles:
- Underbody skid coverage first. It is the cheapest category and the one failure mode, a cracked transfer case or torn-open oil pan, that strands you on the trail.
- Rock sliders second. Rocker panel damage is common on anything with ruts, ledges, or off-camber lines, and a bent rocker panel is a body shop bill, not a bolt-on fix.
- Front bumper last, unless you are winching regularly or running a line with real approach-angle obstacles. The stock Gen 3 bumper survives more than people assume on sand and moderate trail.
None of this matters if the truck never leaves pavement. If your Gen 3 is a daily that sees the occasional fire road, skid plates are the only piece on this list worth the money; sliders and a bumper are for trucks that see real rock and real ruts.
Weight adds up across all three categories once you stack a steel bumper, a full skid package, and sliders. Payload on a Gen 3 Raptor varies by cab, options, and model year, and it is printed on the yellow door-jamb sticker for your specific truck, not in a spec sheet online. None of the armor makers publish a combined installed weight for bumper plus skids plus sliders, so check that sticker and weigh the truck at a CAT scale with your full build on it before you assume you have payload left over for passengers and gear.
The short version
- Skid plates first: the Juggernaut USA Full Skid Plate Package at roughly $1,565-1,780 covers the most ground with the easiest install; the RCI Full Skid Plate Package at $660-797 is the budget path to similar coverage, and the standalone RCI transfer case skid plate covers just the single highest-consequence spot if the budget is tighter still.
- Rock sliders second: the RCI SuperCrew Rock Sliders at $1,239-1,499 are the bolt-on standard for Gen 3 SuperCrew cabs.
- Front bumper only if you winch or run real obstacles: the ADD Stealth Fighter for approach angle and a real recovery point, the ADD HoneyBadger if you want the winch mount with less added weight.
- Add the ADD Bomber Rear Bumper if your departure angle or a spare-tire carrier matters to your build, and get a quote for your exact spec since rear bumper pricing swings hard on options.
- Total added weight across all three categories is real but not precisely published by any maker. Check the payload rating on your door jamb before you stack everything at once, and treat any specific pound figure, including ours, as unverified.
Deal alert
Shopping for one? Get new listings first
We sweep US dealer inventory and send you new Raptors matching your search — real listings, real asking prices, no spam.